Click for the BBB Business Review of this Home Decor, Accessories & Gifts - Online Retailer  in Chino CA
 





You are here:Home > General Knowledge > More > How to?
We found 0 results matching your criteria.
How to?
  Replacing a Faucet
  Kitchen Faucet Buying tips
  Tips On How to Buy A Bathroom Faucet
Replacing a Faucet
Untitled Document

Replacing Kitchen Or Bathroom Faucet in 8 Steps

Is your old Sink Faucet ugly or does it get in the way when there is a sink full of dishes? Feel Refreshed in Your Kitchen or Bathroom with a new Sink Faucet.

Step One: Choose a Faucet

Select a faucet that requires the same number of openings in the sink that your current faucet has, and the same spacing between those openings.

If it doesn’t, you will NOT need to cut into the sheetrock of the wall but may have to drill a hole in the top on the sink counter. This is in case you do not already have a spray hose and or a soap pump and want one on the side.

Note: For easier installation, instead of using the supply hoses that come with the faucet, consider buying flexible stainless steel supply hoses. These are more reliable and lasts years.

Step Two: Disconnect the Supply Hose and Faucets

It is smart to always wear eye protection when working on Home Remodeling Projects.

Under the sink: turn the handles of the two shut-off valves clockwise as far as you can. If there are no shut-off valves, or if you can’t turn them, turn off the water where it comes into the house.
Turn on the faucets to drain water from the hoses. Use a pipe wrench to remove the hoses from the copper tailpipes under each faucet.

Use a Basin Wrench to unscrew the nuts under the existing faucets and spout - if the nuts are stuck, use penetrating oil to loosen them. Lift off the faucets and spout, and then use a Putty Knife to scrape off any Plumber’s Putty or Caulk from the top of the sink.

Step Three: Install the New Spout and Faucets

Follow the instructions that came with the faucet. They give specific details for installing the spout and handles. The following are general instructions.

Insert the faucets and spout from above the sink, using plumbers putty or silicone to seal them to the surface if they don’t have a sealing gasket.

Under the sink, loosely install the gaskets, washers, nuts and other hardware for the spout and faucets. Align them above the sink and then tighten them securely.

Step Four: Install the Supply Hoses

Clockwise, tightly wrap the threaded fittings at the end of the copper tube under the faucets with Teflon tape - the tape helps form a tight seal.

Use two wrenches to attach the hoses to the faucets (for a two-valve faucet) or connector adapter (for a one-valve faucet): one to hold the copper tube so it doesn’t break off the faucet, and another to tighten the nut.

Place a bucket under the sink to catch leaks. Remove the aerator from the end of the spout - if you can’t unscrew it by hand, wrap a rag around it and turn it with an adjustable wrench. Open the water shutoffs and turn on the faucets for several minutes to clear out any debris. Reattach the aerator.

Step Five: Remove the Old Drain Assembly

Remove old drain assembly, including the sink stopper, the flange (the collar in the sink’s drain opening), the drain body (the pipe just under the drain opening) and its locknut, the lift rod that opens and closes the stopper, and the parts that attach the lift rod to the stopper.

Use the putty knife to scrape old putty and silicone from the drain opening.

Step Six: Install the New Drain Assembly

Place a ring of plumbers putty or silicone sealant around the drain opening and insert the flange from above the sink.
Under the sink, attach the drain body to the flange and then use a pipe wrench to tighten the lock nut to secure the connection. Make sure the flange is tightly seated in the drain hole and remove excess sealant.

Step Seven: Install the Stopper

Drop the lift rod through the hole in the faucet and then, under the sink, attach it to the lift rod strap (the plastic or metal strip with a lot of holes along its length) with the thumb screw or other hardware that comes with the faucet.
Above the sink, insert the stopper into the drain. Under the sink, insert the stopper’s control rod horizontally through the hole in the side of the drain body and then into the hole at the base of the stopper.

Thread the end of the control rod through one hole on the spring clip, through one of the holes in the lift rod strap and then through the other hole in the spring clip.

Use the lift rod to open and close the strainer; if it doesn’t open fully and close tightly, thread the control rod through a different hole in the lift rod strap.

Step Eight: Make sure Everything Works Properly

After all the other steps have been completed and all the joints are tightened sufficiently, turn on the shut-off valves. On the faucet, turn the cold water on first, slowly, just barely open it and then if the water hose or pipes jump, wait for them to quit jumping and then turn the cold water on full blast. This will help prevent any air bubbles that may in the plumbing system from causing the water to splatter everywhere when you use the water. Repeat steps on the hot water side.

Supplies:

o Adjustable wrench
o Basin wrench
o Bucket
o Faucet set
o Narrow putty knife
o Penetrating oil
o Pipe wrench
o Plumber’s putty or silicone sealant
o Plumber’s putty
o Protective eye wear
o Putty knife
o Rag
o Teflon tape
o Wrenches

See All Sheetrockers Secrets if you need a quick Fix, Tool, Trick or Tip. Learn Secrets about Sheetrocking, Taping, Mudding and Texturing. Modify trouble spots making repairs easy.

We Help You Turn Your Project into a Pleasure not a Pain. Have what You need at Your Fingertips! Take Pride in Your Own Projects.

[Article Source]

Kitchen Faucet Buying tips

Kitchen Faucet Buying tips

KS8178DLLS

A durable and stylish kitchen faucet or bath faucet blends together function and aesthetics. The well made faucet makes life a lot easier. Excellent valve mechanism and more durable finishes boost longevity and looks.

Here are six steps in choosing the right faucet for you:

1. Two-handle designs, generally goes for as low as $50, allows you to regulate the temperature more accurately. Having independent control for the hot and cold water makes adjusting the temperature easier.

The single handle faucets also known as post-mount, generally goes for $75 to $200, operate from side-mounted lever or a top-mounted knob. Most single-handle faucets have pullout spouts.

The cross-shaped design and large wing levers are the more popular designs. However, most faucets have different handles that can be attached to a faucet body for a customized look.

2. If the style of the faucet is important, begin your choosing with the type of finish. The most affordable finish for a faucet is a chrome finish. Usually priced around $60. The chrome-finish has a long warranty on scratches.

The more colorful enamel coatings generally will cost you from $20 to $200 more, and are more susceptible to scratches and chipping. Add 25 to 40 percent more to the price of coated faucets for stainless steel faucets.

3. A PVD (physical vapor deposition) finish is better than usual plated finishes but add $150 to $750 more in costs. The PVD finish is done by vaporizing the metal and glazing it with a scratch-resistant and non-tarnishing film.

Look at brushed chrome, oil-rubbed bronze and satin nickel for a rustic appeal. The brushed finish and satin finish cleverly hides scratches.

4. There are more to spouts aside from the standard straight faucets. There are high-arching goose-like spouts, great for filling pots. A pull-out faucet can get you anywhere in a sink with three-bowls. You can go from a spray mode to a stream mode with a touch. There are also restaurant-type models for those extra long hoses.

5. Know that there are four kinds of faucets.

a. The compression valve:

The compression valve uses rubber washers. The compression valve type of faucet will eventually leak but they are typically easy to repair.

b. The ball valves:

The ball valve controls the flow and temperature of the water by using a steel ball. The ball valves are washerless and easy to maintain because of this. Replacing a ball valve is readily affordable and easy to do.

c. The ceramic disk

The ceramic disk is virtually a maintenance free water faucet. It is guaranteed not to wear out but is obviously much more expensive than the ball valve or compression valve.

d. The cartridge faucet

Much like the ceramic disk, the cartridge faucet usually does not need any maintenance. Just like the ceramic disk, it has a hefty price tag.

Regardless of the type of faucet you choose. Always check the warranty and the finish.

6. You may opt for filtering faucets, costing $200 plus, to bring in purified water. Several filters are placed under the sink while others are fitted inside the spout. To set the maximum water temperature, an anti-scald faucet can be used. An electronic faucet with an infrared sensor is also available. They save on water and allow for cleaner handles.

In general, you don’t need to hand over your hard earned money to pay for good quality. Most faucets have the same basic parts and sometimes even the same finish across several price lines.

To have a streamlined, urban look, choose a faucet that is mounted on the wall, this is often used with vanity bowls.

Be sure that your faucet connection matches your sink holes. If they don’t match, you’ll have to provide more drill holes or cover the unused holes using an escutcheon plate.

All faucets in general carry at least one year warranties. Even the low-end models carry at least one year of warranty. Many faucets carry a warranty by the manufacturer that is more than one year.

Good luck choosing the perfect faucet for you.

For more great faucet information and resources check out:

[http://www.elegantfaucets.info]

[Article Source]

Tips On How to Buy A Bathroom Faucet

Tips On How to Buy A Bathroom Faucet

If you want to change the look of your bathroom but you don’t have a lot of money, you can do so relatively inexpensively by replacing your sink and faucet. You’ll have lots of choices on the market, many of which are “retro” and look like the faucets in your grandmother’s bathroom. You can also choose from modern-looking chrome faucets or fancy brass fixtures. You can also still buy the old-fashioned crystal-headed faucets with the snub nosed spout. If you’re so inclined, you can buy the old-fashioned key-shaped faucet handles and can choose from porcelain, brass or brushed chrome finish.

It might surprise and please you to know as well that many of today’s faucets are actually multifunctional units that can convert to showerheads or split into separate streams. You can choose from many functions and can even have multiple functions, if you so choose.

Like just about anything else, bathroom faucets run the gamut in terms of price. You can choose from simple and relatively inexpensive to fancy and quite a lot more expensive. Some things to consider before you buy a bathroom faucet include:

What type of handle do you want on your faucets? Single handled faucets rotate to handle all water temperatures from one spigot. You can also buy faucets and handles separately and make your own unique combination. However, if you do this, you have to make sure that the faucet and faucet handles will fit each other.

Next, what style of bathroom faucet will look best in your bathroom? There are hundreds of styles available, anything from antique to modern, and if you so choose, you can even buy 1970s-style faucets. Believe it or not, you can also buy stone faucets that “spit” water out of the wall or those that look like statues from Rome. However, remember that the more complicated your style is, the harder the bathroom faucet will be to install. It will also probably be a lot more expensive than a simpler one.

Next, do you want your bathtub and shower faucets to match those in your sink? Some people don’t consider this important, but it might make your bathroom appear to have a more uniform design if that’s what you’re going for.

Finally, what do you want the bathroom faucet to be made of? They are available in porcelain, chrome, brass, nickel, plastic or even stone. Some creative designers have even made bathroom faucet spouts out of seashells.

Whatever you decide, there are plenty of choices out there available for you to pick something that exactly fits your lifestyle, budget and needs.

Rob Buenaventura has worked in the home improvement industry for several years. Learn more about bathroom vanities, bathroom sinks and other home remodeling ideas at HomeImprovementTouch.com

[Source]

bot